A91B4100000578-0-image-a-2_1429263075293.jpg' alt='My Clear Coat Is Cracking Back' title='My Clear Coat Is Cracking Back' />Diamond Finish Clear Coat Information and Instructions. PRODUCT DESCRIPTIONKBS Diamond Finish Clear. Coat is permanent high solids, single component moisture curing custom Clear Coat. Diamond Finish Clear. Coat is the latest development in ultra high performance clear coats with very high solids over 6. VOCs. Once cured it is incredibly tough and hard like no other clear coat you have used before. This water clear 1. Australias highest UV applications without yellowing or cracking. Diamond Finish Clear. Coat can be applied by brush without brush marks roller and conventional spray gun easily and unlike normal 2 Pak coatings no hardener is needed Diamond Finish Clear. Coat can cure without heat or UV lights in temperatures from 6C to 3. C. This is a unique type of coating in Australia and unlike any other conventional clear coat, so please read the guidelines, directions and warnings thoroughly. IMPORTANT WARNINGSDo not paint out of the can. Keep lid on at all times. Seal can immediately after use. Keep paint groove free of coating try KBS Paint Spouts. If spraying you must follow all warnings and cautions on the can and in directions. SURFACE PREPARATIONFor clear coating over base coat Apply base coat as normal, as per manufactures directions and allow to dry, normally about an hour. ZIMuOg6Ns/TkvtJOvcHfI/AAAAAAAAAH0/UN0XA6YxH1g/s640/100_0687.JPG' alt='My Clear Coat Is Cracking Back' title='My Clear Coat Is Cracking Back' />For clear coating over solid colour or fully cured coatings Clean the surface with conventional surface panel prep solution and or KBS Aqua. Klean, deglaze with 6. For clear coating over metals Metals should be freshly polished or sanded to the finish required and then thoroughly cleaned with high evaporation solvent. An additional clean and light surface etch can be provided as follows For ferrous metals, clean with KBS Aqua. Klean at a dilution rate of 1. Aqua. Klean 1. 0 strength with the use of a soft non abrasive cleaning pad. Rinse the solution immediately and ensure that it is not allowed to sit on the surface. Dry the surface in a way as to minimise water stains. For non ferrous metals aluminum, copper, brass, etc., clean with KBS Aqua. Klean at a dilution rate of 2. Aqua. Klean 4 strength with the use of a very soft non abrasive cleaning pad. Rinse the solution immediately and ensure that it is not allowed to sit on the surface. Dry the surface in a way as to minimise water stains. Remove and clean with fresh water and dry all components including hoses. Coat the seals, ORings and washers with petroleum jelly see Owners Manual for detailed. Outdoor Shades For Heavy Winds The Fortress Zipper Track System with clear vinyl and solid borders is the strongest retractable shade available against the. For all bare metal applications, always use KBS Adhesion Promoter to maximise adhesion of the Diamond. Finish Clear to the substrate metal. For clear coating wood. Prepare as normal eg sand smooth and remove dust. PREPARING FOR APPLICATIONALWAYS USE PROTECTIVE GLOVES AND EYEWEAR WHEN USING DIAMOND FINISH. Ideal application temperatures are 1. C. Use only in moderate to dry atmospheric conditions i. Do not shake can. DO NOT PAINT OUT OF CANAfter a good stir, dispense a working amount of Diamond Finish Clear. Coat into a separate container steel or glass is best and seal original can immediately. Unused paint should NEVER be put back into the can as it will shorten its shelf life and cause pressure build up possibly popping the lid. Keep can groove free of paint by using a scoop or KBS Paint Spout. Find the latest business news on Wall Street, jobs and the economy, the housing market, personal finance and money investments and much more on ABC News. Plasterwork refers to construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative. Using Pidgin With Microsoft Office Communicator Hidden. History. Nail polish originated in China and dates back to 3000 BC. Around 600 BC, during the Zhou dynasty, the royal house preferred the colors gold and silver. Use plastic wrap between the lid and the top of the can to stop metal to metal contact as Diamond Finish Clear. Coat can permanently seal the lid. If there is any trouble resealing the can lid tightly, transfer and store Diamond Finish in a proportionally sized clean glass jar. Always store in a cool dry place. APPLYING DIAMOND FINISH CLEARCOATApply Diamond Finish Clear. Coat to clean dry prepared surfaces using a bristle brush, foam brush, roller, or spray equipment. Diamond Finish has superior self leveling. What is an isolation coat An isolation coat is a coat between your finished painting and the varnish. It is transparent and creates a physical separation between the. The easiest way to keep your voice from cracking is to soothe your throat with warm tea, hydrate it with water, and clear it with vocal lozenges. I concluded at the age of 15 or 16 that I had no interest in biology, or medicine, or any of those aspects of science that dealt with this messy thing called life. I am experiencing problems witht the dura touch finish on my 20 ga gold hunter. The finish has become tacky and not comfortable to hold. I am very disapointed with. Brush marks will flow out. When brushing apply thin covering coats. IF SPRAYING, ALWAYS WEAR AN AIR SUPPLIED RESPIRATOR AND EYE PROTECTION NIOSHMSHA approved organic vapor particulate respirator. Thinning is not generally required if brushing, for spraying 1. Use KBS 1 Thinner. ONLY. When spraying Spray pressure of 3. Always apply a MINIMUM of 2 covering coats, first coat thin covering followed by moderate to full coat 5. For marine or industrial applications, apply a MINIMUM of 3 thin covering coats 5. Re coating can be done once the first or consecutive coat is dry to touch and does not leave a fingerprint. Remember to clean your spray gun immediately after using Diamond Finish. FOR BEST END RESULTS, always apply coats consecutively within 6 hours of each coat curing. Average cure times are 1 2 hours, depending on humidity levels. NOTEDo not apply Diamond Finish in wet or humid conditions to avoid rapid curing. Do not apply Diamond Finish too thick or too quick between coats. In each of these instances, surface bubbling may result as released carbon dioxide becomes entrapped beneath the top surface layer of paint. CLEAN UPUse KBS 1 Thinner or gun clean for immediate clean up including your spray gun. IMPORTANT Remember Diamond Finish must be cleaned up before it dries. It cannot be removed by any solvent once cured. Always wear protective gloves to avoid skin contact and temporary staining. If skin contact accidentally occurs, immediately remove with 1 Thinner or lacquer thinner followed by soap and water. If Diamond Finish should stain your skin, only the course of time will remove it. GENERAL PAINTING TIPS AND GUIDESIf painting in conditions of high temperature and humidity thin Diamond Finish more than normal to avoid gassing. Do not use UV or bake lights to cure Diamond Finish. Diamond Finish will take 4 days to become hard under normal conditions and will continue to harden over the following weeks. In spray booths use low air flow and moderate temperatures for curing. Diamond Finish can be cut and polished as a normal clearcoat after 2. Back to Diamond Finish Clear. Coat Product Page.